2024 Utility Trailer Flatbeds 4000AE® Drop Deck
ONE STEP AHEADOur flatbeds give you the assets that improve profitability
UNQUESTIONED
INNOVATION OF A HIGHER CALIBER
It flat-out betters the bottom line
Features may include:
Light weight, high strength, low maintenance- The 4000AE delivers the strength and durability of an all-steel trailer and the low weight benefit of an all-aluminum trailer.
- Designed with 3" aluminum crossbars, that include nine 4" full-width, tapered aluminum crossbars on 8" centerlines to provide optimized strength at the coil.
- Attached to the extruded aluminum floor, the 80,000 psi high strength steel hat-shaped top flange provides additional lateral stability to the trailer.
- The main beams are shot blasted to bare metal prior to painting and then coated with a two-part primer and two-part urethane top coat on the exterior surfaces. A rust preventative coating is applied to the interior surfaces of the beams for lower maintenance cost.
- Our patented crossmembers system is featured on the 4000AE. A combination of 3" and 4" aluminum crossmembers replace steel to optimize weight without compromising strength or functionality.
- Three tube-shaped outriggers located on each side of the flatbed are connected to the aluminum crossmembers, providing stability and helping distribute the load to the main beams.
- 2024
- Utility Trailer
- Flatbeds
- 4000AE® Drop Deck
- Flatbed
- 73,000 lb
- 80,000 lb evenly distributed mainbeam
- Kingpin location: 30" from front | Rubber dock bumpers: (2) ½" proud mounted on rear rail
- 48' 0"
- 59⅝" front deck height on 47" height 5th wheel
- 102"
- Front gooseneck: 12⅜"
- Deck type: 21" drop with 11' 0" front deck and 40¼" rear deck height | Kingpin plate: Integral with approach plate | Kingpin type: AAR hardness cruciform | Run up members: 4 steel angles run up members | Support legs: Jost® model A400 square 2-speed steel crank type | Support leg location: 120" from leading edge of front rail to center line of support legs | Support leg shoe type: 10" × 10" hinged square low profile sand support leg shoes | Support leg crank location: Roadside of support legs || Floor type: 1⅛" extruded aluminum flat top floor with hardwood nail strips at each side rails (2) | Floor joint sealant: Caulking applied prior to assembly between aluminum planks and wood nailers | Front wall lining: ¼" exterior grade plywood | Conspicuity tape location: On rub rail | Frame finish: Utility black enamel with primer undercoat on all steel show surfaces; aluminum parts receive a natural finish | Vertical & horizontal I.C.C. bumper finish: Utility black enamel on horizontal bumper, black scharpf on vertical bumper | Bottom side rail finish: Natural aluminum | Top front & top side rail finish: Extruded aluminum | Support leg finish: Rust preventative coating | Mudflap type: Black plastic anti-sail with Utility logo, mounted with steel reinforcing straps | Slack adjusters: Bendix® Versajust® automatic | Axle manufacturer: Hendrickson® N-spindle type | Hub piloted system with outboard drums: 10 stud hub-piloted system with outboard cast drums with 16½" × 7" brakes included with ConMet Preset Plus® | Hubcaps: Federal-Mogul “non-vented”
- Front rail: Aluminum with stainless steel front corners | Vertical and horizontal I.C.C. bumper: D.O.T. high strength steel vertical with non-slip 7" deep horizontal | Front panels: .050" pre-painted white aluminum | Front wall posts: 2" extruded aluminum Zee | Front corner post: 7 ga. formed steel
- Coil reinforcing: Reinforcing for single 39,000 lb coil operation with 5 pairs of outriggers | Coil package reinforcement: 5' span of 4" tapered end aluminum crossmembers in coil reinforcing area on 8" center lines | Side pockets: ¼" extruded aluminum outside-type pockets on 24" center line | Crossmembers: 3" aluminum I-beam crossmembers on 12" center line full length, 28" center line over tires | Frame web: 22" deep 7 ga. steel 60,000 psi one-piece | Bottom flange: ⅝" × 4" high strength steel 80,000 psi | Top flange: 7 ga. hat section 80,000 psi high strength steel | Rub rail: ⅜" × 3" extruded aluminum with recess for conspicuity tape on sides only | Side rail: 5⅜" deep extruded aluminum with integral sliding winch track on each side | Hendrickson air ride system with integral axles: Hendrickson® AANL 23K INTRAAX air ride with LDA axles and 121" axle spacing | Axle spindle nuts: ConMet® included with Preset Plus®
- Approach plate: ¼" steel, 45" wide, front 9" tapered up 3"
- Fixed air ride suspension location: 96" center line to rear
- Air actuation system: 1 tank with spring brakes | Air brake chambers: Bendix® EnduraSure™ 3030 | Anti-lock brake system (ABS): Bendix® TABS-6 2S/1M | Brake lining style: Hendrickson® HXS brake lining style
- Wheel bearings: ConMet® included with Preset Plus® | 22.5" × 8.25" standard width wheels: Factory choice steel 10 hub piloted wheels | Wheel bearing lubrication: Mobilube HD Plus 80W-90 oil
- BFGoodrich 255/70R 22.5 ST230 16 ply, load range H | Oil seals:Curtain tensioner assembly: V-shaped furling spool mounted above a ratchet base and lock at front
- Electrical receptacle: 7-way without circuit breakers | Main harness: Utility moisture-resistant 6-wire harness with internal ground and 7-way plug
- Light weight hubs: ConMet aluminum | Stop, tail, turn lights: Grote® 4" LED (10-diode) lights, 2 per side with black snap-in flange
- Dallas, Texas
- New
- 2024
- Utility Trailer
- Flatbeds 4000AE® Drop Deck
- Coil reinforcing: Reinforcing for single 39,000 lb coil operation with 5 pairs of outriggers | Coil package reinforcement: 5' span of 4" tapered end aluminum crossmembers in coil reinforcing area on 8" center lines | Side pockets: ¼" extruded aluminum outside-type pockets on 24" center line | Crossmembers: 3" aluminum I-beam crossmembers on 12" center line full length, 28" center line over tires | Frame web: 22" deep 7 ga. steel 60,000 psi one-piece | Bottom flange: ⅝" × 4" high strength steel 80,000 psi | Top flange: 7 ga. hat section 80,000 psi high strength steel | Rub rail: ⅜" × 3" extruded aluminum with recess for conspicuity tape on sides only | Side rail: 5⅜" deep extruded aluminum with integral sliding winch track on each side | Hendrickson air ride system with integral axles: Hendrickson® AANL 23K INTRAAX air ride with LDA axles and 121" axle spacing | Axle spindle nuts: ConMet® included with Preset Plus®
- Available